High-pressure homogenizers · Cell lysis

Cell disruption,
at 4–6 °C.

JNBIO homogenizers reach 2,070 bar and keep the entire sample path in a 4–6 °C bath. Three models, from 3 ml on the bench to 6 litres per hour. TELOTECH, JNBIO's exclusive general agent for Europe, demonstrates them in your laboratory, installs them and trains your team.

207 MPa
Maximum pressure (2,070 bar)
4–6 °C
Bath along the entire path
1.5 to 6 L/h
Flow rate by model
Cold along the entire path
Inlet, valve and outlet sit in a 4–6 °C bath, to limit the heating caused by passing under pressure.
Metal seals
Sealing relies mainly on metal seals, with no rubber O-rings. The valve is made of diamond.
Controlled and logged
Touchscreen and PLC: live pressure curve, alarms, 7-day operation history, password access, emergency stop.
One contact in France
On-site demonstration, installation, training and a one-year warranty, in direct contact with the manufacturer's engineers.
Three models

From method development to multi-litre batches.

Same maximum pressure, same cold bath, same diamond valve. The choice depends on your batch volume and the flow rate you need.

European launch in preparation

JN homogenizers are being brought into conformity with European regulations. We are already organizing demonstrations in your laboratory and answering your questions; sales will open once this step is complete.

Benchtop · Small batches

JNBIOJN-Mini Pro

Method development, small batches and scarce samples, from 3 ml.

207 MPa
Maximum pressure
1.5 L/h
Maximum flow rate
3 ml
Minimum volume
4–6 °C
Cooling bath
  • In-line cleaning with pressurized water
  • Separate machine and chiller, on the bench
  • The model we use for demonstrations
View details
Laboratory · Medium batches

JNBIOJN-2.5C

Regular batches from a few hundred millilitres to a few litres.

207 MPa
Maximum pressure
2.5 L/h
Maximum flow rate
5 ml
Minimum volume
< 1 ml
Residual volume
  • Cleaning and sterilization in place (CIP/SIP)
  • Negative-pressure drainage as an option
  • In-line filtration as an option
View details
Laboratory · Large batches

JNBIOJN-6.0C

Batches of several litres, the highest flow rate in our current range.

207 MPa
Maximum pressure
6 L/h
Maximum flow rate
4–6 °C
Cooling bath
CIP/SIP
Cleaning in place
  • Cleaning and sterilization in place (CIP/SIP)
  • 500 ml processed in 5 minutes per pass, at maximum flow rate
  • To scale up from the lab towards pilot
View details
Compare the models in detail
Applications

Break the walls, recover the contents.

Disruption is mechanical: the sample passes under high pressure through a narrow valve. No beads to remove afterwards, no lysis detergent to get rid of.

Bacterial lysis

E. coli and most bacteria

Lysates for purifying recombinant proteins and enzymes.

  • E. coli
  • Recombinant proteins
  • Enzymes
Tough walls

Yeasts and spores

Saccharomyces, Pichia, Ganoderma spores: tougher walls that need higher pressure and several passes.

  • S. cerevisiae
  • Pichia pastoris
  • Ganoderma
Extraction

Proteins and nucleic acids

Lysis step upstream of protein and nucleic acid purification, with the sample kept cold.

  • Proteins
  • DNA and RNA
  • Upstream of purification
Applications, disruption rates and limits of use
Technology

Four design choices.

Each one addresses a specific problem of high-pressure lysis: valve wear, seals, sample heating, pressure stability.

01 — Diamond valve

A valve harder than tungsten carbide

The homogenizing valve is made of diamond, a material harder than tungsten carbide and ceramics. The manufacturer reports wear several tens of times slower.

02 — Metal seals

No rubber O-rings

Sealing of the high-pressure circuit relies mainly on metal seals. There are no rubber O-rings to replace regularly.

03 — Full cold bath

4 to 6 °C from inlet to outlet

The inlet coil, the high-pressure pump and valve, and the outlet coil are immersed in the same 4–6 °C bath. The sample stays cold throughout the pass.

04 — Hydraulic drive

Stable pressure, stop and restart under pressure

The pump is driven hydraulically, with no compressed air. Pressure stays stable, and the machine can be stopped and restarted without releasing the pressure.

Demonstration and service

Try it on your samples, in your lab.

01

On-site demonstration

We bring a JN-Mini Pro to your laboratory, install it and process your own samples over at least half a day.

02

Installation and commissioning

On your site, by our team, until operation is verified with your staff.

03

User training

Operation, cleaning, routine maintenance and first-line troubleshooting.

04

One-year warranty

From acceptance of the installation, with the manufacturer's technical support.